Credit Card Merchant Services
>

Enter Your Email To Sign Up
For Our E-Newsletter:


You are here: Home > Billet Accesories
Sort By:
Page of 2
Integrated Engineering -6an Coolant Adapter Fitting
List Price: $24.99
Our Price: $17.99
Save $7.00!

This coolant adapter fitting will allow you to use a factory coolant temp sensor location to plumb a -6an line for your water cooled turbocharger, or anything else you need coolant for. These are made to clip into the factory coolant temp sensor port used on MANY VW/Audi applications.

Features:
Made from 6061 aluminum
Male -6an outlet
Integrated Engineering M12x1.5 Coolant Temp Sensor Adapter
List Price: $24.99
Our Price: $17.99
Save $7.00!

When installing a standalone ECU, finding a location for your coolant temperature sensor can be a bit tricky. We have designed these adapter bungs to clip into the factory VW/Audi coolant temperature sensor location, for a painless installation. These are tapped with M12x1.5 threads, which are commonly found on GM, Delphi, and some Bosch coolant temperature sensors.

Features:
Fits MANY VW/Audi engines
Uses Delphi sensor #TS10076 or equivalent

A must for standalone ECU users.
Integrated Engineering -10an Valve Cover Breather Adapter 24V VR6
List Price: $24.99
Our Price: $17.99
Save $7.00!

Integrated Engineering has a solution for your custom breather/catch can setups! These nifty little pieces install in place of the factory hose barb in your valve cover to provide you with a -10an outlet for plumbing in a catch can, or just to convert over to braided lines. Installation takes less than 10 minutes, with no welding required!

Features:
Made from 6061 aluminum.
-10an male outlet
10 minute installation
Fits all late 2.8/3.2L 24V VR6 engines

Installation is a breeze. Simply remove factory hose barb with pliers and tap IE adapter in with a rubber mallet.
IE Billet Spacer for 06A Mechanical Timing Tensioners
List Price: $22.99
Our Price: $18.49
Save $4.50!

Stevebilt is proud to offer Integrated Engineering's Billet Mechanical Timing Tensioner Spacer. This is the spacer needed to use a mechanical timing belt tensioner on your 06A 1.8T engine. These spacers are specifically designed to fit around the back side of the tensioner, to allow for more surface area to bite on. This will eliminate any possibility of the pulley denting in on the backside from over tightening. These spacers now come standard in all of our 06A 1.8T mechanical timing belt tensioner kits.
Integrated Engineering -10an Valve Cover Breather Adapter 06A 1.8T
List Price: $24.99
Our Price: $18.99
Save $6.00!

Integrated Engineering has a solution for your custom breather/catch can setups! These nifty little pieces install in place of the factory hose barb in your valve cover to provide you with a -10an outlet for plumbing in a catch can, or just to convert over to braided lines. Installation takes less than 10 minutes, with no welding required! .

Features:
Made from 6061 aluminum
-10an male outlet
10 minute installation
Fits all late 06A 1.8T engines engines

Installation is a breeze. Simply remove factory hose barb with pliers and tap IE adapter in with a rubber mallet.
Integrated Engineering -10an Valve Cover Breather Adapter 12V VR6
List Price: $24.99
Our Price: $19.50
Save $5.49!

Integrated Engineering has a solution for your custom breather/catch can setups! These nifty little pieces install in place of the factory hose barb in your valve cover to provide you with a -10an outlet for plumbing in a catch can, or just to convert over to braided lines. Installation takes less than 10 minutes, with no welding required!

Features:
Made from
6061 aluminum
-10an male outlet
10 minute installation
Fits all early 12V VR6 engines with metal valve cover

Installation is a breeze. Simply remove factory hose barb with pliers and tap IE adapter in with a rubber mallet.
1.8T SAI Blockoff Plate
List Price: $44.26
Our Price: $22.99
Save $21.27!

Stevebilt is proud to offer Integrated Engineering's 1.8T SAI Block-off Plates. These plates allow the removal of the entire secondary air injection / combi-valve system, including the large injection pump near the oil filter. This results in a much cleaner looking engine bay, as well as less clutter and more room for you to get in there and wrench on your ride. These plates are CNC machined from 6061 aluminum alloy, as well as machined to accept an O ring seal, so they seal up perfectly with no fuss, and no gaskets or messy sealant. The installation is completed with the included aerospace grade Viton O ring, and stainless steel socket head hardware.

Available in red anodized finish only.

Note about check engine lights: There are two codes which may come up for this, one can be solved by adding a resistor to the circuit for the solenoid control valve, the other- for "incorrect flow detected" can only be defeated by software!

Billet Aluminum Breather Adapter for 1.8T, MK4 2.0L
List Price: $42.99
Our Price: $32.99
Save $10.00!

Are you tired of the stock plastic crankcase breather hose always breaking? We have the solution for you! Stevebilt is proud to offer Integrated Engineering's Billet Aluminum Breather Adapter. This nifty little piece fits nicely into the factory bung for the crankcase breather. It features a -10an o-ring threaded port, so you can easily run a braided line, or simply push-lock lines and fittings.

These are a must for anyone looking to build a custom breather setup, or if you just want a bulletproof solution.

Features:
High quality billet aluminum construction
-10an o-ring threaded port
Red anodized finish

Will fit ALL VW 1.8T, and MK4 2.0L engines!

Priced individually
IE 2.5l 5 Cylinder SAI Blockoff Plate Kit
List Price: $79.99
Our Price: $47.99
Save $32.00!

Stevebilt is proud to offer Integrated Engineering's 2.5L 5cyl SAI Block-off Plates. These plates allow the removal of the entire secondary air injection / combi-valve system, including the large injection pump near the oil filter. This results in a much cleaner looking engine bay, as well as less clutter and more room for you to get in there and wrench on your ride. These plates are CNC machined from 6061 aluminum alloy, as well as machined to accept an O ring seal, so they seal up perfectly with no fuss, and no gaskets or messy sealant. The installation is completed with the included aerospace grade Viton O ring, and stainless steel socket head hardware.

Available in red anodized finish only.

This is a complete kit, which includes both blockoff plates, o rings, and mounting hardware!

Note about check engine lights: There are two codes which may come up for this, one can be solved by adding a resistor to the circuit for the solenoid control valve, the other- for "incorrect flow detected" can only be defeated by software!

24v/R32 SAI Blockoff Plate
List Price: $79.99
Our Price: $57.99
Save $22.00!

Stevebilt is proud to offer Integrated Engineering's 24v/R32 SAI Block-off Plates. These plates allow the removal of the entire secondary air injection / combi-valve system, including the large injection pump. This results in a much cleaner looking engine bay, as well as less clutter and more room for you to get in there and wrench on your ride. These plates are CNC machined from 6061 aluminum alloy to ensure a perfect fit, and a beautiful looking piece! The installation is completed with a new gasket, hose fitting, and stainless steel socket head hardware. Comes standard in red anodized finish, also available in raw finish.
   
 

Copyright ©  Stevebilt. All Rights Reserved. Built with Volusion